View RD5CYD08_4315811.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

RD5CYD08
IGBT Driver
REJ03D0180-0700 Rev.7.00 Apr 22, 2008
Description
The RD5CYD08 has two-input AND gate in a 5 pin package. This product is suited as IGBT Driver IC for the strobe.
Features
Supplied on emboss taping for high-speed automatic mounting. Supply voltage range : 4.0 to 6.0 V Operating temperature range: -40 to +85C High drive current IOH short = -130 mA (min) (@VCC = 5.0 V) * Low sink current IOL short = 40 mA (max) (@VCC = 5.0 V) * Ordering Information
Part Name RD5CYD08CME Package Type CMPAK-5 pin Package Code (Previous Code) PTSP0005ZC-A (CMPAK-5V) Package Abbreviation CM Taping Abbreviation (Quantity) E (3,000 pcs/reel)
* * * *
Outline and Article Indication
* RD5CYD08
Index band Marking
D
5
CMPAK-5
= Control code
REJ03D0180-0700 Rev.7.00 Apr 22, 2008 Page 1 of 7
RD5CYD08
Pin Arrangement
IN B
1
5
VCC
IN A
2
GND
3
4
OUT Y
(Top view)
Logic Diagram
A B Y
Function Table
Inputs A L H L H H : High level L : Low level B L L H H Output Y L L L H
Block Diagram
A input
Y output
Internal circuit
B input
REJ03D0180-0700 Rev.7.00 Apr 22, 2008 Page 2 of 7
RD5CYD08
Absolute Maximum Ratings
Item Supply voltage range Input voltage range *1 Output voltage range *1, 2 Input clamp current Output clamp current Continuous output current Continuous current through VCC or GND Maximum power dissipation *3 at Ta = 25C (in still air) Storage temperature Symbol VCC VI VO IIK IOK IO ICC or IGND PT Tstg Ratings -0.5 to 7.0 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 20 50 -200 100 200 200 -65 to 150 Unit V V V mA mA mA mA mW C Test Conditions
VI < 0 or VI > VCC VO < 0 or VO > VCC VO = 0 VO = VCC
Notes: The absolute maximum ratings are values, which must not individually be exceeded, and furthermore no two of which may be realized at the same time. 1. The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed. When Over shoot / Under shoot pulse width is under 10 ns, input and output voltage permit to -1.5 V or VCC+1.5 V. 2. This value is limited to 5.5 V maximum. 3. The maximum package power dissipation was calculated using a junction temperature of 150C.
Recommended Operating Conditions
Item Supply voltage range Input voltage range Output voltage range Operating free-air temperature Note: Symbol VCC VI VO Ta Min 4.0 0 0 -40 Max 6.0 VCC VCC 85 Unit V V V C Conditions
Unused or floating inputs must be held high or low.
Electrical Characteristic
Ta = -40 to 85C
Item Symbol VIH Input voltage VIL VH IOH short Output current IOL short Input current Quiescent supply current Input capacitance IIN ICC CIN VCC (V) 4.0 4.5 to 5.5 4.0 4.5 to 5.5 4.0 5.0 4.0 5.0 4.0 5.0 5.5 5.5 5.0 Min VCCx0.7 VCCx0.7 -- -- -- -- -65 -100 20 30 -- -- -- Typ -- -- -- -- 0.35 0.40 -85 -130 28 40 -- -- 2.5 Max -- -- VCCx0.3 VCCx0.3 -- -- -105 -160 40 50 5 10 -- Unit Test condition
V
VO = 0 V mA VO = VCC A A pF VIN = 5.5 V or GND VIN = VCC or GND, IO = 0 VIN = VCC or GND
REJ03D0180-0700 Rev.7.00 Apr 22, 2008 Page 3 of 7
RD5CYD08
Switching Characteristics
VCC = 4.0 V
Item Propagation delay time Output rise time Output fall time Symbol td(ON) td(OFF) tr tf Ta = -40 to 85C Min Typ Max -- -- 80 -- -- 160 -- -- 1000 -- -- 2000 Unit Test Conditions FROM (Input) TO (Output)
ns
CL = 4000 pF
A or B
Y
VCC = 5.0 0.5 V
Item Propagation delay time Output rise time Output fall time Symbol td(ON) td(OFF) tr tf Ta = -40 to 85C Min Typ Max -- -- 70 -- -- 140 -- -- 800 -- -- 1500 Unit Test Conditions FROM (Input) TO (Output)
ns
CL = 4000 pF
A or B
Y
REJ03D0180-0700 Rev.7.00 Apr 22, 2008 Page 4 of 7
RD5CYD08
Test Circuit
VCC
Pulse generator
Input
Output
50
CL = 4000 pF
Note: CL includes probe and jig capacitance.
Waveforms
VCC Input 50% 50% GND t d(ON) tr t d(OFF) tf
90% Output 10%
90%
VOH
10%
VOL
Note: Input waveform : duty cycle 50%
REJ03D0180-0700 Rev.7.00 Apr 22, 2008 Page 5 of 7
RD5CYD08
Application Note (Strobe circuit)
Luminescence Circuit
Trigger trance
Xenon tube
IGBT Driver IGBT
Control IC
Combination example
SYSTEM IGBT 3.3 V RJP4002ANS RJP4002ASA RJP4003ANS RJP4003ASA IGBT Driver RD3CYD08 RD3CYDT08 RD5CYD08 RD5CYDT08 Control IC 3.3 V signal 5.0 V signal 3.3 V signal
5.0 V
IGBT Driver Lineup
TYPE No. RD3CYD08 Specification VCC = 2.0 to 3.6V CMOS lever input IOH(short) = -130mA(typ) @ VCC = 3.3V IOL(short) = 45mA(typ) @ VCC = 3.3V VCC = 2.0 to 3.6V CMOS lever input IOH(short) = -130mA(typ) @ VCC = 3.3V IOL(short) = 45mA(typ) @ VCC = 3.3V VCC = 4.0 to 6.0V CMOS lever input IOH(short) = -130mA(typ) @ VCC = 5.0V IOL(short) = 40mA(typ) @ VCC = 5.0V VCC = 4.0 to 6.0V TTL lever input IOH(short) = -130mA(typ) @ VCC = 5.0V IOL(short) = 40mA(typ) @ VCC = 5.0V Package CMPAK-5 VSON-5
RD3CYDT08
CMPAK-5
RD5CYD08
CMPAK-5
RD5CYDT08
IGBT Lineup
TYPE No. RJP4002ANS RJP4002ASA RJP4003ANS RJP4003ASA Specification VCES = 400V(max), ICP = 150A(max), 2.5V drive VCES = 400V(max), ICP = 150A(max), 2.5V drive VCES = 400V(max), ICP = 150A(max), 4V drive VCES = 400V(max), ICP = 150A(max), 4V drive Package VSON-8 TSSOP-8 VSON-8 TSSOP-8
REJ03D0180-0700 Rev.7.00 Apr 22, 2008 Page 6 of 7
RD5CYD08
Package Dimensions
JEITA Package Code SC-88A RENESAS Code PTSP0005ZC-A Previous Code CMPAK-5 / CMPAK-5V MASS[Typ.] 0.006g
D e
A Q c
E
HE LP L
A xM
A S A b
L1
A3 e
Reference Symbol
Dimension in Millimeters
A2
A
yS b b1 c c1
A1 S e1
A A1 A2 A3 b b1 c c1 D E e HE L L1 LP x y b2 e1 l1 Q
Min 0.8 0 0.8 0.15 0.1 1.8 1.15 1.8 0.3 0.1 0.2
Nom
0.9 0.25 0.22 0.2 0.13 0.11 2.0 1.25 0.65 2.1
Max 1.1 0.1 1.0 0.3 0.15 2.2 1.35 2.4 0.7 0.5 0.6 0.05 0.05 0.35 0.9
l1
b2 A-A Section Pattern of terminal position areas
1.5 0.25
REJ03D0180-0700 Rev.7.00 Apr 22, 2008 Page 7 of 7
Sales Strategic Planning Div.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Notes: 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries.
RENESAS SALES OFFICES
Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7858/7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2377-3473 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 3518-3399 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145
http://www.renesas.com
Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510
(c) 2008. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .7.2

▲Up To Search▲

Price & Availability of RD5CYD08

	To Download RD5CYD08 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .